Linksys MX4000 and Device Reconnection Issue [Resolved]

The number of users owing Linksys mesh systems is high. The reason being, their ability to transform any internet dead zone into a high-speed internet zone. But, these days, a few users are experiencing weird issues with their mesh systems. Recently, a user owning Linksys MX4000 nodes complained about the device reconnection issue. His problem went the following way:

I have three A3 devices and added two new Linksys nodes to my home network to have a better connectivity on all of them. All three devices are flaunting the latest version of firmware. The problem started with my Samsung TV and eventually expanded to all devices in the house. All the devices get disconnected automatically and I’ve to enter the WiFi password again. This happens several times during the day especially in the morning. I’m tired of this repeated cycle. What to do? Any help will be appreciated.

A Bigger Picture: Linksys MX4000 Device Reconnection Issue

Before we start troubleshooting the issue, let us study the matter. This must be known to you that devices generally get disconnected when they are over the internet for a longer period. Perhaps, a few devices like iOS phones and smart gadgets were connected to the Linksys node for a quite large period due to which they disconnected automatically.

As far as the problem of entering the WiFi password again and again is concerned, it can simply resolved by forgetting the network on each connected device and reconnecting them back. This might help you a lot. But, if the problem is still the same, it is suggested that you walk through the hacks that we’re going to discuss further.

Resolved: Linksys MX4000 Nodes and Device Reconnection

1. Restart the Velop System

There is a high probability that the problem is with the Linksys nodes system itself. Keep in mind that nothing is certain in the technical realm and any device can fall victim to technical glitches. This time, it might be your Linksys MX4000 node. Therefore, you are suggested to power down your Linksys nodes one by one and disconnect them from their respective power outlets. After waiting for 10-15 minutes, you can power them up once again and connect all your devices. Check if you are required to go for the repeated connectivity cycle again or not. If yes, then move to the next point.

Note: You are also suggested to power cycle your client devices no matter wired or wireless. It can also help you avoid the hassle of re-connecting to the WiFi network of your Velop nodes again and again.

2. Disconnect a Few Devices

Perhaps, your Linksys MX4000 WiFi network is overloaded due to which some devices are getting disconnected continuously. The only solution you are left with in this case is to disconnect a few devices from the Velop network. You can try disconnecting those gadgets that do not require internet access 24/7. After that, check if the problem you were facing has been resolved or not. You must also check for WiFi leeches. It can be done by accessing the Linksys Velop setup URL on a computer and checking the list of connected devices. Block the suspicious devices as soon as possible.

3. Update Your Velop

Sometimes, it is an annoying pending firmware update due to which a Velop node bugs on the connected devices. So, you very well know what to do in that scenario. Just, pull up the Linksys Velop on a mobile device that is already present on the Velop MX4000 network and check if a new firmware version is available for any of the nodes you have added to your mesh system. If yes, then update it as soon as possible.

Quick Tip: Try updating only one node at a time and then verify whether the issue gets fixed. This is because, it is not recommended to update all nodes concurrently.

4. Check for Parental Controls

Did you enable Parental Controls on your Velop system at the time of the setup process? Yes? Looks like, in a hassle, you set rules for all the devices present in the network system and the result is what you know already. The best way to get the problem fixed is to change the Parental Controls rule for the devices. You can do this by accessing the linksyssmartwifi.com URL on a computer/laptop connected to the Linksys MX4000 node. Change the rules and see how it changes the game for you.

The Concluding Words

That’s all about how to resolve the Linksys MX4000 Velop and the device reconnection issue. We are hopeful that after taking the help of the techniques highlighted above, you will be able to make your network system faultless. On the off-chance, the problem is adamant to leave your side, you should not hesitate to perform a factory default reset of the entire Velop network and set it up from scratch. This time, you can try experimenting with the status of the nodes. In other words, attempt to use the primary one as secondary and vice-versa.